7 Most Effective Ways to Solve Airlock in Water Pump

26 December 2023

Imagining a hot day in the dry season, Sobat Honda must be hoping  for a water pump that can help to provide a large flow of water for your agricultural land. However, suddenly the water pump had an airlock problem that disrupted the water flow. This situation can certainly distrupt the Sobat hinder Sobat Honda farming process. But don't worry, there are solutions that can help solves airlock in the water pump or insufficient suction power.

When the water pump has an airlock, the causes can vary. Starting from leaks in the installation channels that allow air to enter to damage the water pump components. But take it easy because there are practical steps that can be taken to solve this problem and get back the water flow that  Sobat Honda needs.

Choose the right solution to overcome airlock in the water pump and see the complete information in this article to get to know the causes and the right solution.

Causes of Airlock in Water Pump?

Sobat Honda, in the context of water pumps, the problem of the airlock describes a condition in which the water pump cannot pump water smoothly, or there is resistance in the flow of water due to the presence of air. Several causes could cause this problem to occur. Let's understand the causes of airlock water pumps:

Read also: 3 Causes Low Water pressure on Water Pump and Their Solutions

1. Leaks in the Installation Hose

One of the main causes of airlock in the water pump is a leak in the hose installation. Leaks can occur due to a cracked part of the hose, a damaged seal, or a connection that is not tight.

When there is a leak, air from outside can enter the installation channel and interfere with the performance of the water pump. Sobat Honda, it is important to periodically check the installation ducts and repair leaks immediately to prevent the airlock problems.

2. Insufficient amount of water to be sucked

The water pump requires sufficient water to suck and pump water properly. If there is too little water, the pump will suck in the air instead.

This can happen if a well, river, reservoir, or other water source runs dry or there is a water supply problem. It is important to ensure adequate water availability before operating the pump.

3. Damaged Valve

A broken valve can also cause airlock in a water pump. The valve regulates water flow in and out of the pump. If the valve is damaged, air can enter the pump system and interfere with its performance.

An inlet valve that is worn, dirty, or not working correctly can cause this problem. Be sure to periodically clean and check the condition of the valve so that the pump can operate smoothly.

4. The Condition of the Thread Socket is Less Tight

A less tight or loose threaded socket can cause the water pump to get airlock. The threaded socket connects the hose and the water pump, which must be tight to prevent air from entering the system, Sobat Honda.

If the threaded socket is not tight enough, air can get into the hose and interfere with the proper flow of water. Be sure to check and repair the thread socket position regularly so that the pump can operate properly.

How to Solving Airlock in Water Pump

After knowing the cause of the water pump getting airlock, Sobat Honda needed to know how to deal with the problematic water pump properly. Because of that, Honda Power Products will share a full review of the various ways to deal with an airlock water pump that Sobat Honda can try. Here's a full explanation:

1. Replace The Hose

If the airlock in the water pump is caused by a leak in the hose during the installation, the first step to take is to replace the leaking hose. Check thoroughly and find the part that leaks. Replace damaged equipment with new ones and ensure the hose connections are tight and waterproof. This will help prevent air from entering the system.

2. Make Sure The Installation of The Suction Hose Is Correct

Incorrect installation of the suction hose can also cause the water pump to get airlock. Ensure the suction hose is appropriately and securely attached to the water pump. Make sure there are no leaks or gaps that could allow air to enter. Reattach the suction hose properly and ensure it is tight to prevent air leaks.

3. Bait the Pump with Water

One way to solve the problem of airlock in a water pump is to bait the pump with water. Take a container filled with water and connect the suction hose directly to the container. Turn on the pump and let the water run for a few minutes. This process will help remove air from the pump system and replace it with water.

Read also: Here's How to Primming Water Pumps Easily

4. Check and Correct the Position of the Thread Socket

Check the position of the threaded socket on the water pump again. Ensure the connection between the hose and pump is sufficiently tight and tight. If a loosely threaded socket is found, tighten it using a wrench. Make sure no air can enter through the connection. Periodically check the position of the threaded socket to prevent airlock.

5. Clean the Valve

If the valve is damaged, which is the cause of airlock, try cleaning the valve. Remove the valve from the pump and clean it using a small brush or soft cloth. Ensure the valve is in good condition and no dirt or damage could interfere with the water flow. If the in valve is damaged, consider replacing it with a new one.

Knowing the causes and how to deal with airlock water pumps, will help to solve the problem immediately, and the water pump system can function properly again. It is essential to carry out routine checks and maintenance on the water pump system to prevent similar problems. Please keep it clean and pay attention to the condition of the hoses and pump components to maintain optimal performance.

Sobat Honda have looked at the various possible causes as well as the solutions. It's essential to know these causes so you can take the proper steps to fix the problem.

Remember that good maintenance is essential in keeping the water pump running. Carrying out regular inspections, cleaning dirty components, and making necessary repairs will help prevent airlock on Sobat Honda's water pump. So you can ensure a consistent and uninterrupted water flow, providing comfort and convenience. Sobat Honda needs to know that choosing a quality water pump can also help prevent the problem of airlock.

The reason is the spare parts used in it are original. You can choose Water Pump - WB20XN NF from Honda Power Products.

This water pump can be used for various needs, such as irrigating rice fields and construction with high suction power according to customer needs. Equipped with a 4-stroke GX160 engine, this water pump is easy to turn on and use and has a longer lifespan.

Are you interested in trying it? Find the best and most trusted water pump according to your needs only at Honda Power Products.

Honda Power Products Indonesia

Honda Power Products menyediakan mesin serbaguna, generator, pemotong rumput, pemotong sikat, pompa air, dan mesin tempel.